Kratky system designs
From Kratky Method Hydroponics, a reference on passive, non-circulating hydroponics
| Developer | Bernard A. Kratky, University of Hawaii CTAHR[1] |
|---|---|
| First patent filed | August 5, 1992[2] |
| Shared principle | One fill of nutrient solution, a fixed or supported cover, and a falling solution level[1] |
| Power needed | None: no pumps, aerators, wicks or electricity[3] |
| Smallest design | A 4-liter bottle holding one lettuce plant[1] |
| Largest design | A 757-liter tank holding twelve tomato plants[4] |
Kratky system designs are the container layouts Dr. Bernard A. Kratky published for his suspended-pot, non-circulating hydroponic method, from a one-plant bottle to commercial lettuce tanks and large containers for tomatoes and cucumbers.[1][4] Every design follows the same idea: the whole crop is grown with one application of water and nutrients made before planting, and no electricity or pumps are used.[1] The designs differ in container size, in how the cover is held, and in which crops they can carry to harvest.
For how the method works in general, see Kratky method hydroponics.
The shared principle
In every Kratky design, a seedling grows in a small container of growing medium held by a cover over a tank of nutrient solution. At planting, the lower part of that container sits in the solution, so the medium is wetted by capillary action and the young plant is watered automatically.[1] As the plant drinks, the level falls below the container. By then roots have grown out of it: the lower roots take up water and nutrients, and the upper roots live in the moist air under the cover.[1]
Kratky listed four basic concepts that every design must respect:[1]
- The upper part of the root system should be exposed to air with high relative humidity.
- Roots must not be allowed to dry out.
- The lower part of the root system should gather water and nutrients.
- The solution level may stay the same or be lowered, but it may not be raised, or the roots will "drown".
The designs
| Design | Crop | Container and cover | Source |
|---|---|---|---|
| Capillary tube method | Leaf and semi-head lettuce | Covered container or lined tank; seedlings in tapered tubes with side holes | Patents 1995 and 1996[2] |
| Bottle method | One lettuce plant | Darkened 4 L bottle; net pot held by the neck | 2004, 2009[1][5] |
| Covered tank method | Leaf, romaine and semi-head lettuce | Lined tank 5½ in (14 cm) deep; polystyrene cover resting on the frame | 2009, 2010[5][3] |
| Float-support method | Lettuce | Raceway tank; raft floats at planting, then rests on two pipes | 2008, 2009[6][5] |
| Tomato and cucumber systems | Cucumbers, tomatoes | 100–130 L trash container, lined barrel or large tank | 2004, 2005[1][4] |
| Watercress method | Watercress | Lined tank 5½ in or deeper, suspended or floating cover | 2015[7] |
Choosing a design by water need
Because no water is added after planting, the container must hold all the water the crop will use. That single fact decides which design suits which crop.
- The bottle method suits only crops that need less than 4 liters of water over their life, such as lettuce. A 200 gram lettuce plant in Hilo typically used about 3 to 4 liters.[1]
- The commercial covered tank method is meant only for crops that need less than 2 gallons of water per plant from transplanting to harvest. Tanks are filled with 1.5 to 2 gallons of solution per plant.[3]
- Tomatoes typically need 25 to 40 liters of water per kilogram of fruit, so a fill-once tomato tank must be very large. Kratky called that version "an academic curiosity except in special situations".[1] His later tomato work kept a shallow level with float valves instead.[4]
Order of development
The first patent for the method was filed in 1992 and issued in 1995; it describes tapered tubes held by a light-blocking lid, wetted by capillary action.[2] A 2002 home-garden kit used a one-gallon bottle to grow one lettuce plant and became the prototype for the commercial method.[3] Kratky's 2004 paper set out the bottle, tank, tomato and cucumber designs together.[1] The float-support method followed in trials in Hawaii and Pennsylvania in 2008,[6] and the 2010 bulletin gave commercial growers full instructions for the covered tank.[3] The full chronology is in the history of the Kratky method.
See also
- Kratky method hydroponics
- How to set up a Kratky system
- Crops tested with the Kratky method
- History of the Kratky method
Terms used on these pages are defined in the glossary of the Kratky method.
References
- Kratky, B.A. (2004). "A suspended pot, non-circulating hydroponic method." Acta Horticulturae 648: 83–89. PDF.
- Kratky, B.A. "Non-circulating hydroponic plant growing system." U.S. Patent 5,385,589, filed August 5, 1992, issued January 31, 1995. Patent.
- Kratky, B.A. (2010). A Suspended Net-Pot, Non-Circulating Hydroponic Method for Commercial Production of Leafy, Romaine, and Semi-Head Lettuce. University of Hawaii CTAHR, Vegetable Crops VC-1. PDF.
- Kratky, B.A., G.T. Maehira, R.J. Cupples and C.C. Bernabe (2005). "Non-circulating hydroponic methods for growing tomatoes." Proceedings of the National Agricultural Plastics Congress 32: 31–36. PDF.
- Kratky, B.A. (2009). "Three non-circulating hydroponic methods for growing lettuce." Acta Horticulturae 843: 65–72. PDF.
- Kratky, B.A., G.T. Maehira, E.J. Magno, M.D. Orzolek and W.J. Lamont (2008). "Growing lettuce by a float-support non-circulating hydroponic method in Hawaii and Pennsylvania." Proceedings of the 34th National Agricultural Plastics Congress. PDF.
- Kratky, B.A. (2015). Growing Direct-Seeded Watercress by Two Non-Circulating Hydroponic Methods. University of Hawaii CTAHR, Vegetable Crops VC-7. PDF.