Kratky covered tank method
From Kratky Method Hydroponics, a reference on passive, non-circulating hydroponics
Part of Kratky system designs.
| Also called | Suspended net-pot, non-circulating method[1] |
|---|---|
| Crops | Leaf, romaine and semi-head lettuce; also cilantro, green onions, kai choy, pak choi, watercress[1] |
| Tank | Lined, 5½ in (14 cm) deep; commonly 4 × 8 ft or 4 × 16 ft[1] |
| Solution | 1.5 to 2 gal per plant; EC about 1.5 mS[1][2] |
| Cover | ½ to 1 in polystyrene sheets resting on the tank frame[1] |
| Harvest | About 4 to 6 weeks after transplanting[1] |
The Kratky covered tank method is the commercial form of the Kratky method: lettuce in net pots is held by a polystyrene cover resting on the frame of a shallow, plastic-lined tank, and the whole crop grows on the solution put in before transplanting.[1] Kratky set it out for Hawaii growers in his 2010 University of Hawaii bulletin, which notes that the method "can be scaled to home-garden use".[1] It is meant only for crops that need less than 2 gallons of water per plant from transplanting to harvest.[1]
Tank
A tank is a rectangular frame of 2 × 6 lumber on a plywood bottom, 5½ inches deep. Common sizes are 4 × 8 ft and 4 × 16 ft; tanks wider than 6 ft are discouraged because most people cannot reach plants more than 3 ft away.[1] Key points from the bulletin:[1]
- Fill with 1.5 to 2 gallons of solution per plant, so a 50-plant tank holds 75 to 100 gallons.
- Level the tank to within ¾ inch, and build it at a working height of 30 to 36 inches. A full 4 × 8 ft tank weighs more than 800 pounds, so support it at least every 4 ft.
- Line it with two layers of 6-mil black polyethylene, fitted snugly against the sides and bottom and stapled to the outside of the frame.
- Cheaper versions use recycled metal roofing in place of plywood, or set the frame straight on level ground over weed barrier fabric.
- A small leak during a crop can be slowed with a few handfuls of finely milled vermiculite.
Tanks sit in plastic-covered rain shelters or greenhouses with screened sides, because rain would raise the solution level. Outdoor growing is recommended only in dry places.[1]
Cover and spacing
The cover is ½ to 1 inch expanded polystyrene beadboard or extruded polystyrene, cut into 2 × 4 ft sheets that rest loosely on the frame. Plastic pots on the tank floor keep the middle from sagging, and white latex paint extends the cover's life.[1] Holes are cut with a 2-inch hole saw. Two common densities are 1.5 and 1.9 plants per square foot, which gives 48 or 60 plants in a 4 × 8 ft tank; more than two plants per square foot usually crowds large heads.[1] Kratky's papers used 20 × 30 cm spacing for leafy and semi-head lettuce.[2]
Nutrient solution
The tank is nearly filled with water, then two stock solutions are added in equal volumes to reach an EC of 1.5 mS.[2]
| Stock | Per liter of water |
|---|---|
| A | 120 g of a complete hydroponic fertilizer (8% N, 6.6% P, 29.9% K plus micronutrients) and 72 g of magnesium sulfate |
| B | 120 g of soluble calcium nitrate |
Good water quality matters, because salts concentrate as the solution is used. Water starting at an EC of 0.5 mS from contaminants may reach 2.0 mS when a quarter of the solution remains, which can cause tipburn; rainwater is recommended where water quality is poor.[2]
Planting and the crop
Seedlings one to three weeks old go into net pots of growing medium in the cover holes, with the lower ½ to 1 inch of each pot in the solution. The medium is wetted by capillary action. Within a few weeks the solution falls below the pots, leaving a moist air space under the cover; the roots in that space become "oxygen roots", while those in the solution take up water and nutrients.[1]
- Do not lift the cover during the crop, because roots tear.[1]
- Do not raise the level. If a tank looks likely to run dry before harvest, add only about ½ to 1 inch of water or half-strength solution; if that happens all year, switch to deeper tanks.[1]
- Midday wilting is normal and plants recover by late afternoon. Severe wilting can follow a hot, sunny day after cloudy weather; a 30 to 50 percent shade screen is the best remedy.[1]
By harvest, the level has typically dropped 6 to 12 cm.[2]
Harvest and replanting
Leaf and semi-head lettuce is ready about 4 to 6 weeks after transplanting, depending on seedling age, season and cultivar.[1] Growers usually harvest and replant on the same day, so tanks stay full,[2] and by keeping several stages growing they can supply a market every week.[3] Some growers drain and refill after each crop and others top off the remaining solution; as a general rule, tanks should be drained and refilled after every three crops or sooner.[2]
The same tank with a floating cover is described under the float-support method. Step-by-step setup for home growers is in Kratky's setup instructions.
See also
- Kratky system designs
- Kratky bottle method
- Kratky float-support method
- Crops tested with the Kratky method
Further reading
Practical guides from related Kratky sites. These are not sources for the facts on this page.
- Kratky container types, Kratky Containers
References
- Kratky, B.A. (2010). A Suspended Net-Pot, Non-Circulating Hydroponic Method for Commercial Production of Leafy, Romaine, and Semi-Head Lettuce. University of Hawaii CTAHR, Vegetable Crops VC-1. PDF.
- Kratky, B.A. (2009). "Three non-circulating hydroponic methods for growing lettuce." Acta Horticulturae 843: 65–72. PDF.
- Kratky, B.A. (2004). "A suspended pot, non-circulating hydroponic method." Acta Horticulturae 648: 83–89. PDF.